coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
@David and @james*
VGA / DVI-D
Can you check what IC/chip is behind the VGA port on your rev2 / rev3 models since my model doesn't have VGA. Is it a realtek RTD2168 (F7C24P2 GF48E) DP to VGA converter (like the OptiPlex 3050/5040 accessory)? If so you can probably change "Analog" from `gma-mainboard.ads` into "eDP" and probably also dump one of the HDMI ports in there since I only see a single DVI-D(check during boot, not the OS if you still have output, except VGA).
If you accompany that with the following line in `Kconfig` `select SOC_INTEL_GFX_ENABLE_DDI_E_BIFURCATION` than VGA might start working in the OS (Linux / WIndows with proprietary intel gpu driver), not during POST/BOOT since libgfxinit doesn't know yet how to work with it.
Please check when on OEM firmware what the output of `xrandr` is when having a VGA display connected (fedora 42 mate, lists all the correct outputs without a display connected), you can drop all the resolution/modes output in your log I'm only interested in used connector as in (HDMI-A-2, VGA, DP1, DP3 etc), do the same for DVI-D.
PCIe
Can you post if one of you have a "1X length PCIe device" inside a 1X length slot and list the output of `lspci;lspci -tv;lspci -tvn; sudo lspci -vvn;sudo lspci -vvv #really need sudo` and also mention the EXACT label/location on the motherboard in which PCIe 1x slot you put that device when you made the log? Seems rev3 only has one 1x slot, but rev2 has two slots(fill both at same time or create 2 log series with the device first in 1 than in the other). This way I can prepare the common `devicetree.cb` for maybe this REV3 `overridetree.cb` variant.
@james
Do you have SPI recovery options?
VGA / DVI-D
Can you check what IC/chip is behind the VGA port on your rev2 / rev3 models since my model doesn't have VGA. Is it a realtek RTD2168 (F7C24P2 GF48E) DP to VGA converter (like the OptiPlex 3050/5040 accessory)? If so you can probably change "Analog" from `gma-mainboard.ads` into "eDP" and probably also dump one of the HDMI ports in there since I only see a single DVI-D(check during boot, not the OS if you still have output, except VGA).
If you accompany that with the following line in `Kconfig` `select SOC_INTEL_GFX_ENABLE_DDI_E_BIFURCATION` than VGA might start working in the OS (Linux / WIndows with proprietary intel gpu driver), not during POST/BOOT since libgfxinit doesn't know yet how to work with it.
Please check when on OEM firmware what the output of `xrandr` is when having a VGA display connected (fedora 42 mate, lists all the correct outputs without a display connected), you can drop all the resolution/modes output in your log I'm only interested in used connector as in (HDMI-A-2, VGA, DP1, DP3 etc), do the same for DVI-D.
PCIe
Can you post if one of you have a "1X length PCIe device" inside a 1X length slot and list the output of `lspci;lspci -tv;lspci -tvn; sudo lspci -vvn;sudo lspci -vvv #really need sudo` and also mention the EXACT label/location on the motherboard in which PCIe 1x slot you put that device when you made the log? Seems rev3 only has one 1x slot, but rev2 has two slots(fill both at same time or create 2 log series with the device first in 1 than in the other). This way I can prepare the common `devicetree.cb` for maybe this REV3 `overridetree.cb` variant.
@james
Do you have SPI recovery options?
Last edited by walterav on Sun Aug 10, 2025 10:01 am, edited 1 time in total.
-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
OEMdavid wrote: ↑Sat Aug 09, 2025 9:56 am ...Recently i got 9600k and tested it on rev 3.0 with modified microcodes updates on Original bios and me disabled it works but only on cold boot mean i need to power off and power on from atx power supply strange behavior but i remeber you had somthing similar with your Xeon so just decided to post it...
This cold boot only issue was fixed for Xeon (kabylake without iGPU) using the corporate ME version injected by the Coffeetime tool.
But only getting the Xeon to work with no tools or hacks just requires the kabylake chip firmware to be in the BIOS (which was already the case) and just disable ME not sure if it was HAP or neutering or both. Recenty got the insight to play with both and neuter specific ME partitions.
But for warm boots / reboots I really needed the coffeetime tool corporate ME injected (or waiting more than x minutes before soft on) .
Coreboot
Strange note using the altered donor ME, which worked fine on OEM Asrock BIOS won't work with Coreboot at all... Although coreboot natively support kabylake processor but still use a IDF with a HAP bit enabled so it works only on coldboots (BTW needed a lot more hacking to get a iGPU-less XEON to work with coreboot but other story).
-
james2
- Posts: 15
- Joined: Sat Aug 09, 2025 6:37 am
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
sure, yes it only has one PCI, (I am using an nvidia gtx1060 with it. )
I will be using a ch341A / Pomona SOIC8
I will be using a ch341A / Pomona SOIC8
Code: Select all
lspci;lspci-tv; lspci -tvn; lspci -vvn;sudo lspci -vvv
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers (rev 05)
00:01.0 PCI bridge: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) (rev 05)
00:14.0 USB controller: Intel Corporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller (rev 31)
00:14.2 Signal processing controller: Intel Corporation 100 Series/C230 Series Chipset Family Thermal Subsystem (rev 31)
00:16.0 Communication controller: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #1 (rev 31)
00:17.0 SATA controller: Intel Corporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] (rev 31)
00:1c.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #5 (rev f1)
00:1c.5 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #6 (rev f1)
00:1f.0 ISA bridge: Intel Corporation H110 Chipset LPC/eSPI Controller (rev 31)
00:1f.2 Memory controller: Intel Corporation 100 Series/C230 Series Chipset Family Power Management Controller (rev 31)
00:1f.3 Audio device: Intel Corporation 100 Series/C230 Series Chipset Family HD Audio Controller (rev 31)
00:1f.4 SMBus: Intel Corporation 100 Series/C230 Series Chipset Family SMBus (rev 31)
01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 6GB] (rev a1)
01:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 02)
zsh: command not found: lspci-tv
zsh: exit 127 lspci-tv
-[0000:00]-+-00.0 8086:591f
+-01.0-[01]--+-00.0 10de:1c03
| \-00.1 10de:10f1
+-14.0 8086:a12f
+-14.2 8086:a131
+-16.0 8086:a13a
+-17.0 8086:a102
+-1c.0-[02]--
+-1c.5-[03]----00.0 10ec:8168
+-1f.0 8086:a143
+-1f.2 8086:a121
+-1f.3 8086:a170
\-1f.4 8086:a123
00:00.0 0600: 8086:591f (rev 05)
Subsystem: 1849:591f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 0
Capabilities: <access denied>
Kernel driver in use: skl_uncore
lspci: Unable to load libkmod resources: error -13
00:01.0 0604: 8086:1901 (rev 05) (prog-if 00 [Normal decode])
Subsystem: 1849:1901
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 121
IOMMU group: 1
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: e000-efff [size=4K] [16-bit]
Memory behind bridge: de000000-df0fffff [size=17M] [32-bit]
Prefetchable memory behind bridge: c0000000-d1ffffff [size=288M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:14.0 0c03: 8086:a12f (rev 31) (prog-if 30 [XHCI])
Subsystem: 1849:a12f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 124
IOMMU group: 2
Region 0: Memory at df110000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:14.2 1180: 8086:a131 (rev 31)
Subsystem: 1849:a131
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
IOMMU group: 2
Region 0: Memory at df12e000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel_pch_thermal
00:16.0 0780: 8086:a13a (rev 31)
Subsystem: 1849:a13a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 126
IOMMU group: 3
Region 0: Memory at df12d000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:17.0 0106: 8086:a102 (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: 1849:a102
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 125
IOMMU group: 4
Region 0: Memory at df128000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at df12c000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at df12b000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1c.0 0604: 8086:a114 (rev f1) (prog-if 00 [Normal decode])
Subsystem: 1849:a114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
IOMMU group: 5
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: [disabled] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 0604: 8086:a115 (rev f1) (prog-if 00 [Normal decode])
Subsystem: 1849:a115
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 123
IOMMU group: 6
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: d000-dfff [size=4K] [16-bit]
Memory behind bridge: 88800000-888fffff [size=1M] [32-bit]
Prefetchable memory behind bridge: d2100000-d21fffff [size=1M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 0601: 8086:a143 (rev 31)
Subsystem: 1849:a143
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 7
00:1f.2 0580: 8086:a121 (rev 31)
Subsystem: 1849:a121
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 7
Region 0: Memory at df124000 (32-bit, non-prefetchable) [size=16K]
00:1f.3 0403: 8086:a170 (rev 31)
Subsystem: 1849:d887
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 128
IOMMU group: 7
Region 0: Memory at df120000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at df100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1f.4 0c05: 8086:a123 (rev 31)
Subsystem: 1849:a123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
IOMMU group: 7
Region 0: Memory at df12a000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 0300: 10de:1c03 (rev a1) (prog-if 00 [VGA controller])
Subsystem: 3842:6267
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 129
IOMMU group: 1
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [size=128]
Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nouveau
01:00.1 0403: 10de:10f1 (rev a1)
Subsystem: 3842:6267
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
IOMMU group: 1
Region 0: Memory at df080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
03:00.0 0200: 10ec:8168 (rev 02)
Subsystem: 1849:8168
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
IOMMU group: 8
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at d2110000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at d2100000 (64-bit, prefetchable) [size=64K]
Expansion ROM at 88800000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers (rev 05)
Subsystem: ASRock Incorporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
Kernel driver in use: skl_uncore
00:01.0 PCI bridge: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal decode])
Subsystem: ASRock Incorporation 6th-10th Gen Core Processor PCIe Controller (x16)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 121
IOMMU group: 1
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: e000-efff [size=4K] [16-bit]
Memory behind bridge: de000000-df0fffff [size=17M] [32-bit]
Prefetchable memory behind bridge: c0000000-d1ffffff [size=288M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: ASRock Incorporation 6th-10th Gen Core Processor PCIe Controller (x16)
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00218 Data: 0000
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <8us
ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16
TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 75W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCap: CRSVisible-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd-
AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Via WAKE#, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+ EqualizationPhase1+
EqualizationPhase2+ EqualizationPhase3+ LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Capabilities: [d94 v1] Secondary PCI Express
LnkCtl3: LnkEquIntrruptEn- PerformEqu-
LaneErrStat: 0
Kernel driver in use: pcieport
00:14.0 USB controller: Intel Corporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller (rev 31) (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 124
IOMMU group: 2
Region 0: Memory at df110000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee00298 Data: 0000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:14.2 Signal processing controller: Intel Corporation 100 Series/C230 Series Chipset Family Thermal Subsystem (rev 31)
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family Thermal Subsystem
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
IOMMU group: 2
Region 0: Memory at df12e000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal
00:16.0 Communication controller: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #1 (rev 31)
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family MEI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 126
IOMMU group: 3
Region 0: Memory at df12d000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee002f8 Data: 0000
Kernel driver in use: mei_me
Kernel modules: mei_me
00:17.0 SATA controller: Intel Corporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: ASRock Incorporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 125
IOMMU group: 4
Region 0: Memory at df128000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at df12c000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at df12b000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee002b8 Data: 0000
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci
Kernel modules: ahci
00:1c.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #5 (rev f1) (prog-if 00 [Normal decode])
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family PCI Express Root Port
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
IOMMU group: 5
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: f000-0fff [disabled] [16-bit]
Memory behind bridge: fff00000-000fffff [disabled] [32-bit]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM not supported
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #8, PowerLimit 10W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCap: CRSVisible-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00238 Data: 0000
Capabilities: [90] Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [100 v0] Null
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:1c.5 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #6 (rev f1) (prog-if 00 [Normal decode])
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family PCI Express Root Port
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 123
IOMMU group: 6
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: d000-dfff [size=4K] [16-bit]
Memory behind bridge: 88800000-888fffff [size=1M] [32-bit]
Prefetchable memory behind bridge: d2100000-d21fffff [size=1M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #6, Speed 5GT/s, Width x1, ASPM not supported
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #9, PowerLimit 10W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCap: CRSVisible-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00278 Data: 0000
Capabilities: [90] Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v0] Null
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:1f.0 ISA bridge: Intel Corporation H110 Chipset LPC/eSPI Controller (rev 31)
Subsystem: ASRock Incorporation H110 Chipset LPC/eSPI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 7
00:1f.2 Memory controller: Intel Corporation 100 Series/C230 Series Chipset Family Power Management Controller (rev 31)
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family Power Management Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
IOMMU group: 7
Region 0: Memory at df124000 (32-bit, non-prefetchable) [size=16K]
00:1f.3 Audio device: Intel Corporation 100 Series/C230 Series Chipset Family HD Audio Controller (rev 31)
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family HD Audio Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 128
IOMMU group: 7
Region 0: Memory at df120000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at df100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D3 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00338 Data: 0000
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1f.4 SMBus: Intel Corporation 100 Series/C230 Series Chipset Family SMBus (rev 31)
Subsystem: ASRock Incorporation 100 Series/C230 Series Chipset Family SMBus
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
IOMMU group: 7
Region 0: Memory at df12a000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 6GB] (rev a1) (prog-if 00 [VGA controller])
Subsystem: eVga.com. Corp. GP106 [GeForce GTX 1060 6GB]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 129
IOMMU group: 1
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [size=128]
Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00358 Data: 0000
Capabilities: [78] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x16
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range AB, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete+ EqualizationPhase1+
EqualizationPhase2+ EqualizationPhase3+ LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [250 v1] Latency Tolerance Reporting
Max snoop latency: 71680ns
Max no snoop latency: 71680ns
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [420 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Capabilities: [900 v1] Secondary PCI Express
LnkCtl3: LnkEquIntrruptEn- PerformEqu-
LaneErrStat: 0
Kernel driver in use: nouveau
Kernel modules: nouveau
01:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1)
Subsystem: eVga.com. Corp. GP106 High Definition Audio Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
IOMMU group: 1
Region 0: Memory at df080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 75W
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x16
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range AB, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 02)
Subsystem: ASRock Incorporation Motherboard (one of many)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
IOMMU group: 8
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at d2110000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at d2100000 (64-bit, prefetchable) [size=64K]
Expansion ROM at 88800000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Endpoint, MSI 01
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10W
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [b0] MSI-X: Enable+ Count=2 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
pcilib: sysfs_read_vpd: read failed: No such device
Not readable
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1]
Kernel driver in use: r8169
Kernel modules: r8169-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
Thanks for the input @james2, noticed that your realtek NIC is also listed on 1c.5 / PCIE Root Port 6 just like the REV2 variant.
Do you also happen to have a "1X length PCIe device" to test in the "1X slot" than I can confirm or alter the `overrideetree.cb` for your specific H110M_DVS_R3, if not you probably have to order a 1X PCIe ethernet NIC anyway since the onboard REALTEK doesn't seem to work in coreboot at all?
Can you also verify the Realtek CHIP near the VGA port, if it is indeed a DP to VGA converter, or list output on fedora 42 if your don't have a VGA/DVI-D monitor? Assuming you have a CPU with iGPU enabled as well besides your PCIE dGPU (or remove dGPU once for test if your motherboard doesn't support multi)?
iGPU
Also if you booted with iGPU can you upload a copy of `data.vbt` with BIOS revision you got it from and md5sum / sha256sum, thats the final thing I miss for a real good REV3 third variant. The location might be a little bit different adres wise, but try to find with a root terminal and extract `i915_vbt`
Currently I have a buildable (not yet tested) 3 variant code base for the H110M-DVS-R2/R3(NCT6776 example edits) and H110 Pro BTC+ will post soon on review.coreboot.org WIP.
Do you also happen to have a "1X length PCIe device" to test in the "1X slot" than I can confirm or alter the `overrideetree.cb` for your specific H110M_DVS_R3, if not you probably have to order a 1X PCIe ethernet NIC anyway since the onboard REALTEK doesn't seem to work in coreboot at all?
Can you also verify the Realtek CHIP near the VGA port, if it is indeed a DP to VGA converter, or list
Code: Select all
xrandriGPU
Also if you booted with iGPU can you upload a copy of `data.vbt` with BIOS revision you got it from and md5sum / sha256sum, thats the final thing I miss for a real good REV3 third variant. The location might be a little bit different adres wise, but try to find with a root terminal and extract `i915_vbt`
Code: Select all
sudo dd if=/sys/kernel/debug/dri/0000\:00\:02.0/i915_vbt of=dataR3a.vbt
sudo cat /sys/kernel/debug/dri/0000\:00\:02.0/i915_vbt > dataR3b.vbt
md5sum dataR*
sha256sum dataR*
-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
BTW @david / @james
What is the diagnosis currently of the REV3 running coreboot?
Doesn't it poweron at all or stay off silent, maybe just ETH/LAN or PS2/USB light up after PSU connects?
(no idea what it can be...)
Does it poweron / stayon but no activity on screen / nor serial but do ps/2 usb devices light up?
(maybe hangs on RAM init?)
Does it poweron and less than a second after that poweroff immediately and stay off?
(probably ME like failures with unofficial CPU's?)
Does it poweron stay on for a couple of seconds than restarts (poweroff/poweron again) but not enough time to reach POST or iGPU/dGPU output?
(probably WDT watch.dog.timer that resets the system, maybe all is well except is resets until you fix superio/gpio wdt adres?)
What is the diagnosis currently of the REV3 running coreboot?
Doesn't it poweron at all or stay off silent, maybe just ETH/LAN or PS2/USB light up after PSU connects?
(no idea what it can be...)
Does it poweron / stayon but no activity on screen / nor serial but do ps/2 usb devices light up?
(maybe hangs on RAM init?)
Does it poweron and less than a second after that poweroff immediately and stay off?
(probably ME like failures with unofficial CPU's?)
Does it poweron stay on for a couple of seconds than restarts (poweroff/poweron again) but not enough time to reach POST or iGPU/dGPU output?
(probably WDT watch.dog.timer that resets the system, maybe all is well except is resets until you fix superio/gpio wdt adres?)
-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
Coreboot g1e11bda5d0c9 testbuild for the H110M-DVS_REV3 with incorrect donor 'data.vbt' from H110M-DVS_REV2 with altered minimal superio replacement code for nct6776, EDK2 mrchromebox 2505 with dGPU option rom loading, only Top down enabled no Above 4g nor REBAR.
Image build without IFD nor ME regions flash using following command internally:
Its also good practice to test Serial COMPORT output in OEM bios, for example with minicom /dev/ttyS0, before flashring coreboot...
@david can you allow file upload for my account in this forum?
Image build without IFD nor ME regions flash using following command internally:
Code: Select all
sudo umount /sys/firmware/efi/efivars
sudo flashrom --ifd -i bios -p internal -w h110m-dvs-r3_cb_edk2mrcb2505_g1e11bda5d0c9_nct6776.rom --noverify-all
# don't reboot shutdown nor reset
#!!! pull power / PSU cord !!!
#wait a minute, try turning on?
@david can you allow file upload for my account in this forum?
-
david
- Site Admin
- Posts: 394
- Joined: Sat May 21, 2016 7:50 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
Ok i did it 20MB max file size 500MB per user.
Here is one test i did attached seabiosrom for rev.2.0.
Let me know is it works for you guys.
Here is one test i did attached seabiosrom for rev.2.0.
Let me know is it works for you guys.
You do not have the required permissions to view the files attached to this post.
-
david
- Site Admin
- Posts: 394
- Joined: Sat May 21, 2016 7:50 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
As far i remeber from last time i flashed it with rev 2.0 bios it turn on when i power on and that is fan spin and get stuck no boot.walterav wrote: ↑Sun Aug 10, 2025 1:21 pm BTW @david / @james
What is the diagnosis currently of the REV3 running coreboot?
Doesn't it poweron at all or stay off silent, maybe just ETH/LAN or PS2/USB light up after PSU connects?
(no idea what it can be...)
Does it poweron / stayon but no activity on screen / nor serial but do ps/2 usb devices light up?
(maybe hangs on RAM init?)
Does it poweron and less than a second after that poweroff immediately and stay off?
(probably ME like failures with unofficial CPU's?)
Does it poweron stay on for a couple of seconds than restarts (poweroff/poweron again) but not enough time to reach POST or iGPU/dGPU output?
(probably WDT watch.dog.timer that resets the system, maybe all is well except is resets until you fix superio/gpio wdt adres?)
Same cpu works with same coreboot on rev 2.0 perfectly.
-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
Thanks for fixing file upload, good to know that the machine powered on and stayed on but probably no post/screen/serial output?
Diagnose?
Does it respond on reset button, does it respond on keyboard USB/PS2 CTRL-ALT-DELETE do you notice difference in fan speed?
While it stays on can you try the first time after (cold boot), 10-15 seconds after poweron to permanent ground yourself for instance on the shielded ethernet port grap it, than remove the CMOS clear jumper from "normal" and for a couple of seconds put the jumper on the "clear/enable" mode and than back to "normal" all while the systems is still running (be carefull not to damage the board or yourself)! Wait half a minute or longer since RAM training/ME for first time can take some time. See if something pops up on your screen If you have 2 different type of memory DIMMS go back to one and try each slot, also try a native supported CPU. You probably need a dGPU in case of your early coreboot image.
Can you please upload a "data.vbt" for the REV3 so I can sent a complete image using your earlier REV 3 whole rom dump for IFD and ME regions:
This way I can sent an image that supports both iGPU even dual GPU and works with all dGPU since option ROM loading is now supported native by EDK2 (mrchromebox 2502/05). If you don't have a working serial port its atleast good to know if iGPU/dGPU may work.
I saw on one of the better Asrock website motherboard pictures that there is indeed a Realtek branded chip near the VGA connector can you please verify which?
The most obvious hardware difference are in scope, but software wise I noticed that comparing to original REV2 to REV3 ROM the REV3 has a more tight firmware lockdown policy but both of you have external SPI flashers. In my case I could flash REV2 on BTC+ on OEM ROM just the BIOS region and have coreboot working.
Good news is that both revisions have the exact same sized BIOS region but slightly offset ME region/size... so those BIOS regions are main focus. No other ME hacks or IFD hacks yet.
Diagnose?
Does it respond on reset button, does it respond on keyboard USB/PS2 CTRL-ALT-DELETE do you notice difference in fan speed?
While it stays on can you try the first time after (cold boot), 10-15 seconds after poweron to permanent ground yourself for instance on the shielded ethernet port grap it, than remove the CMOS clear jumper from "normal" and for a couple of seconds put the jumper on the "clear/enable" mode and than back to "normal" all while the systems is still running (be carefull not to damage the board or yourself)! Wait half a minute or longer since RAM training/ME for first time can take some time. See if something pops up on your screen If you have 2 different type of memory DIMMS go back to one and try each slot, also try a native supported CPU. You probably need a dGPU in case of your early coreboot image.
Can you please upload a "data.vbt" for the REV3 so I can sent a complete image using your earlier REV 3 whole rom dump for IFD and ME regions:
Code: Select all
md5sum org.rom
ecbb5406e69a4188186052c9b46e9444 org.rom
I saw on one of the better Asrock website motherboard pictures that there is indeed a Realtek branded chip near the VGA connector can you please verify which?
The most obvious hardware difference are in scope, but software wise I noticed that comparing to original REV2 to REV3 ROM the REV3 has a more tight firmware lockdown policy but both of you have external SPI flashers. In my case I could flash REV2 on BTC+ on OEM ROM just the BIOS region and have coreboot working.
Good news is that both revisions have the exact same sized BIOS region but slightly offset ME region/size... so those BIOS regions are main focus. No other ME hacks or IFD hacks yet.
-
walterav
- Posts: 41
- Joined: Sat Sep 07, 2024 7:08 pm
Re: coreboot on ASRock H110M-DVS rev 3.0 and rev 2.0 and me_cleaner
@david trying to upload a working ME region that works for warm boot/Xeon (also in coreboot) since the REV2 / PBTC+ has a fraction smaller ME it fits. Try to insert it only with ifdtool in your current working whole ROM dump and flash the whole ROM back does it fix your warmboot issue?
Can you hint where to upload a file or is it only possible as topic starter?
Code: Select all
REV3 me size 2093056
PBTC me size 2084864
ifdtool -i me:PBTCMEXWBOK.bin rev3wholedump.bin -p sklkbl
#sorry forgot the platform quirk, this needed for any ROM/IFDTOOL editing...